Bad Mister introduces us to the next lesson in leveraging the power of the MONTAGE - using the Part Assignable Knobs.
PERFORMANCE 9: Assignable Knobs
The previous examples were showing how to use the Assignable Knobs of the Performance Parts for building Super Knob assignments. Independent of the Super Knob use, you can use the Part Assignable Knobs for individual assignments, which are used after selecting the Part. (Please note: The Live Set that is used in the Mastering MONTAGE series is located here
: You can control only one Part at the same time with Assignable Knobs (the currently selected/highlighted PART). But you can use the Super Knob and the Assignable Knobs of the *selected* Part at same time!
This example shows how Super Knob assignments can be combined with individual assignments to the Part Assignable Knobs, which are not routed to the Super Knob. Getting your head around this may take some time, but before there was a Super Knob, an Assignable Knob would be assigned to control a specific parameter within the current PART. This can still be done, and it remains unaffected by the movement of the Super Knob for this PART. Often a PART of your PERFORMANCE may be selected (highlighted) for individual direct
play/control, while the others are responding to messages generated by the Arpeggiator. For example, you might have a two Part split Performance, a lead sound in the right hand and a bass in the left; you might want to have a knob that just affects the lead Part. In such a case you may opt to simply use the Assignable Knob independent of the Super Knob movement.
Each PART, when selected for direct play/control, has access to the three rows of eight Knob functions plus it's own eight Assignable Knobs. In affect, you have 32 Knobs, plus the physical controllers (MW, PB Wheel, the two Assignable Switches, Ribbon, Aftertouch, FC1/FC2, Faders (Control Sliders)), the Motion Sequences, Arpeggios, the Envelope Follower, etc., that can all be called upon while this Part is selected. An extensive Receive Switch matrix allows you to determine which physical controllers are active per
Part, thus making your performing work as necessary. Between the Super Knob which can work independently, and the controls available to your currently highlighted (selected) Part, you can design most any scenario.
This example Performance includes only one Part with a typical fat sawtooth synth pad. All eight Part Assignable Knobs are assigned to parameters within this PART, but only two of them (1 + 2) are also
routed/linked to the Super Knob:
Translation: In the previous examples of the SUPER KNOB assignment, we saw how on the Performance upper "COMMON/Audio" level you needed to assign "Part 1 Assign 1", "Part 1 Assign 2" and so on, to make each Knob accessible via the Super Knob. In this example only these first two are using the Super Knob. The other six Knobs are individually accessible when you highlight/select the PART, as we'll see below. (This is very similar to the Motif XS/XF Performance where when you selected an individual PART, the Assign 1 and 2 Control Knobs would address just that individual PART parameters).
To view the Assignable Knob layout go to the OVERVIEW screen: [SHIFT] + [PERFORMANCE (HOME)] or from the main screen touch "MOTION CONTROL" > "OVERVIEW".
First view the Performance COMMON
Assignable Knob assignment:
Change the PART parameter from "COMMON" to "PART 1" to view the Assignable Knob layout for PART 1:
There is one DESTINATION parameter assignment to each of the PART's eight Assignable Knobs.
To view the actual 8 Destination Control Settings use the "Edit Part 1 Control Settings" shortcut.
Set the DISPLAY FILTER
You can view Destination 1 ~ Destination 4 on the first Page.
There are two PAGES:
The currently displayed "DESTINATION" (blue) has a number 1-16, touch that designation to view it's data. Touch the parameter setting to view an overlay of possible parameter Destinations.
Looking at DESTINATIONs 1 and 2, (above) you learn that CUTOFF and RESONANCE are being controlled by AssignKnob 1 and AssignKnob 2, respectively. Because the AUTO SELECT is active (green) moving the SUPER KNOB will reveal that, indeed these are the "PART 1 ASSIGN 1" and "PART 1 ASSIGN 2" parameters that are linked to the movement of the Super Knob:
The Super Knob starts with the center position (64). This is useful for combining with the use of Part Assignable Knobs, which are set to center position by default. For this reason selecting Bipolar
(Polarity) for all assignments in the Part Controller Box is needed: Bipolar allows you to move the parameter up or down depending on whether a Positive or Negative value is set for RATIO. Positive values increase as the Knob is turned clockwise.
The Assignable Knobs can be used for controlling the listed eight parameters: Cutoff, Resonance, Insert "A" Dry/Wet, Insert "A" LFO Speed, Insert "A" Feedback Level, Element LFO Pitch Modulation Depth (vibrato), AEG Attack, AEG Release.
At same time you can use the Super Knob, which controls the Assignable Knobs 1+2. But you should avoid using the Super Knob and
the Assignable Knobs 1+2 at same time, because they are controlling the same parameter.
You can see the movements of the Super Knob at the LEDs of the Assignable Knob 1+2.
I've edited and stored this PERFORMANCE renaming the individual Destinations for this PART (PART 1) (DISPLAY NAME). By default, they are simply named: Assign 1, Assign 2, Assign 3, Assign 4 and so on.
This DISPLAY NAME
will appear on the main PERFORMANCE screen when PART 1
is the "selected" (highlighted) PART. Shown below:
When you *select* the PART, Part 1, the name you provide as the "Display Name" will appear - very useful when performing to know what your assignable knobs are going to do (select the Part by pressing [PART SELECT 1/1] or
by touching the TYPE/NAME box above PART1) – Now you will see that I've identified what each of them is doing to PART 1. Because you can SELECT only one PART at a time, it makes total sense to be able to read what that Knob is assigned to (this cuts down immensely on the guessing about what a Knob is doing!) It appears that many of the PRESETs have the word "Assigned" simply as the PART "Display Name" – which at least lets you know it is doing something – if it is not assigned the Display name area appears blank.Using the "Display Name":Hint
: From the upper COMMON/Audio level (or when the PERFORMANCE NAME is highlighted) the KNOBS will simply read ASSIGN 1 – ASSIGN 8. When you select an individual PART (either by touching the PART Name or by pressing [PART SELECT 1/1] ~ [PART SELECT 8/8] you have the option of viewing the KNOB assignment by what it is doing. You can even give it a "nickname" – it can be anything that you wish. This is extremely cool because you can be descriptive. The Presets only indicate with Knob is "Assigned" when you select an individual PART.
Imagine the PART Knob is controlling an FM Element that causes RING MODULATION when you raise its Modulation Index (Output Level) saying it is "Output Level" is not as helpful as naming it "+RingMod".
So selecting any single PART 2-8 (so that it is the highlighted PART) will show you what each of the knobs is assigned to control. This can be very useful and can make exploring Performances much easier because when scuba diving
, it can get quite deep!
If you have any questions or comments about this article, please join us to discuss them on the Forum here
Catch up on the previous article in the series - "Mastering MONTAGE 7: Super Knobs Values" here
Next article now available: "Mastering MONTAGE 9: Controller Box Switches" - access here