Synth Forum

Notifications
Clear all

AN1X Problem with richness. Sound is not rich and should be?

3 Posts
2 Users
0 Likes
426 Views
Posts: 0
New Member
Topic starter
 

I have problem with my AN1X.
When I played it one time sound is rich and nice and while after sound is not that reach.
Is there a problem with layers?
When layer pan is off sound is not rich.
When layer pan is set to alternate sound is rich.
But there is a problem
One time is rich and one time not.
How to fix this?
How to set this to not change.
Like every time i press the key sound will be the same?

And second additional thing.
When I pressed key on the synth and in the same time on the software editor sound is richer too but in other way.
What is happening here?
When I pressed key on synth and key in the software?

How to get the best richness of both keys pressed on alternate every time I pressed key to be the same?
or at least how to get the best richness of alternate every time I pressed key to be the same?
I mean how to get this sound if I press one key and every time this sound be the same?

Example software editor settings screenshot

Audio in the attachments

Attached files

Best Richness.rar (360.6 KB)  Holding Key.rar (1.4 MB)  Layer Pan.rar (811.4 KB) 

 
Posted : 10/01/2022 3:40 am
Bad Mister
Posts: 0
 

Hi Albania,
Good to see the old AN1x Editor!

It sounds like what you are describing is a MIDI Routing issue. I suggest the very first thing to try is to disconnect the MIDI connection — just play the AN1x alone, connected to the sound system only. If full sound returns, you will *know* that the issue concerns your MIDI connection.

One cause of thin sound is Routing the same signal through the system twice simultaneously, you’ll get a kind of cancellation.
Check your MIDI Routing and how audio is routed through your system. if you are Routing signal to a computer via an audio interface, you may have different options for monitoring.

Another cause of thin sound deals with the setup of your sound system. Summing a stereo signal improperly to mono, can cause a thin sound due to phase cancellation of the audio signal.

 
Posted : 10/01/2022 3:50 am
Posts: 0
New Member
Topic starter
 

Hi Albania,
Good to see the old AN1x Editor!

It sounds like what you are describing is a MIDI Routing issue. I suggest the very first thing to try is to disconnect the MIDI connection — just play the AN1x alone, connected to the sound system only. If full sound returns, you will *know* that the issue concerns your MIDI connection.

One cause of thin sound is Routing the same signal through the system twice simultaneously, you’ll get a kind of cancellation.
Check your MIDI Routing and how audio is routed through your system. if you are Routing signal to a computer via an audio interface, you may have different options for monitoring.

Another cause of thin sound deals with the setup of your sound system. Summing a stereo signal improperly to mono, can cause a thin sound due to phase cancellation of the audio signal.

Thanks for answer.
I'm using Roland Um-One cable for Midi - USB connection.
I checked but it's the same.
Only on AN1X sound is thick and in alternate layer pan mode is more rich but every key press sound jumping left - center - right.
When I plug-in into usb situation is the same but additionaly I can press key in software and sound is even more rich.
When I set Midi-In to UM-One I can play only on AN1X
When I set Midi-In & Midi-Out to UM-One I can additionaly play in software and when I press key both in Software and AN1X sound is different, more rich than only on AN1X without USB connection and soft.

 
Posted : 10/01/2022 9:13 pm
Share:

© 2024 Yamaha Corporation of America and Yamaha Corporation. All rights reserved.    Terms of Use | Privacy Policy | Contact Us