MW10C MW8CX Frequency Response ST OUT, REC OUT, AUX (EFFECT*) SEND, MONITOR OUT -3.0, 0, 1.0 dB, GAIN: min(CH 1-2, CH 3/4-5/6), 20Hz-20kHz, refer to the nominal output level @1kHz Total Harmonic Distortion (THD+N) ST OUT Less Than 0.1 %, +14dBu, 20Hz-20kHz, Input Gain Control at minimum Hum&Noise Hum & Noise are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave attenuation." CH INPUT 1-4 MIC -128 dBu, EIN(Equivalent Input Noise): Rs=150ohms, GAIN:max ST OUT, REC OUT -87 dBu, ST MASTER CONTROL at nominal level and all Ch level controls at minimum. AUX (EFFECT*) SEND -85 dB, All Ch AUX controls at minimum. ST OUT, REC OUT -64 dB, ST Master control and one Ch level control at nominal level. (CH1,2) ST OUT -100 dB, Residual Output Noise. Crosstalk@1 kHz Input to Output -70 dB, STEREO L/R, CH 1-2, PAN panned Hard left or right. Phantom Voltage MIC +48 V USB Audio I/O Sampling Frequency 44.1, 48 kHz, Depend on the application of PC Input HPF CH 1-2 and CH 3/4-5/6, 80Hz, 12dB/oct Input Equalization +15,-15dB maximum. Turn over/roll-off frequency of shelving: 3dB blow maximum variable level. High 10 kHz shelving (CH 1-2, CH 3/4-5/6) Mid 2.5 kHz peaking (CH 1-2, CH 3/4-5/6) Low 100 Hz shelving (CH 1-2, CH 3/4-5/6) High 10 kHz shelving (CH 7/8, CH 9/10**) Low 100 Hz shelving (CH 7/8, CH 9/10**) PEAK Indicator Red LED turns on when post EQ (ST CH: or post Mic HA) signal reaches -3dB below clipping (17dBu). Internal Digital Effect - 16 PROGRAM, PARAMETER control Foot Switch (Digital Effect, on/off) LED Level Meter Pre MONITOR Level 2x7 points LED meter (PEAK,+6,+3,0,-5,-10,-20 dB) PEAK lights if the signal comes within 3 dB of the clipping level. Power Supply Adapter PA-10 Power Consumption 21 W Dimensions W x D x H (mm) 256.6 x 302.5 x 62.2 Net Weight 1.6 kg 1.7 kg Option Microphone Stand Adaptor(BMS-10A) Microphone Stand Adaptor(BMS-10A), Foot Switch (FC5)

	MW12C MW12CX Frequency Response ST OUT, REC OUT, AUX (EFFECT*) SEND, MONITOR OUT -3.0, 0, 1.0 dB, GAIN: min(CH 1-2, CH 3/4-5/6), 20Hz-20kHz, refer to the nominal output level @1kHz Total Harmonic Distortion (THD+N) ST OUT Less Than 0.1 %, +14dBu, 20Hz-20kHz, Input Gain Control at minimum Hum&Noise Hum & Noise are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave attenuation." CH INPUT 1-4 MIC -128 dBu, EIN(Equivalent Input Noise): Rs=150 ohms, GAIN:max ST OUT, REC OUT -88 dBu, ST,REC Master fader at nominal level and all Ch mix controls at minimum. AUX (EFFECT*) SEND -81 dBu, AUX Master control at nominal level and all Ch mix controls at minimum. ST OUT, REC OUT -64 dB, ST,REC Master fader and one Ch fader at nominal level. ST OUT -98 dB, Residual Output Noise. Crosstalk@1 kHz Input to Output -70 dB,STEREO L/R, CH 1-4, PAN panned Hard left or right. Phantom Voltage MIC +48 V USB Audio I/O Sampling Frequency 44.1, 48 kHz, Depend on the application of PC Input HPF CH 1-4, CH 5/6-7/8, 80Hz, 12dB/oct Input Equalization +15,-15dB maximum. Turn over/roll-off frequency of shelving: 3dB blow maximum variable level. High 10 kHz shelving (CH 1-4, CH 5/6-7/8) Mid 2.5 kHz peaking (CH 1-4, CH 5/6-7/8) Low 100 Hz shelving (CH 1-4, CH 5/6-7/8) High 10 kHz shelving (CH 9/10-11/12) Low 100 Hz shelving (CH 9/10-11/12) PEAK Indicator Red LED turns on when post EQ (ST CH: or post Mic HA) signal reaches -3dB below clipping (17dBu). Internal Digital Effect - 16 PROGRAM, PARAMETER control Foot Switch (Digital Effect, on/off) LED Level Meter Pre MONITOR Level 2x12 points LED meter (PEAK,+10,+6,+3,0,-3,-6,-10,-15,-20,-25,-30 dB) PEAK lights if the signal comes within 3 dB of the clipping level. Power Supply Adapter PA-20 Power Consumption 30 W Dimensions W x D x H (mm) 346.2 x 436.6 x 86.1 Net Weight 3 kg 3.2 kg Option - Foot Switch (FC5)
	All fader are nominal when measured. (Nominal position is adjusted to a position that is 6dB lower than the MAX position) Output impedance of signal generator:150ohms *: EFFECT SEND exists only in MW8CX, MW12CX **: ST CH IN 9/10 exists only in MW10C

	ANALOG INPUT CHARACTERISTICS(MW10C / MW8CX) Connections Gain Trim Actual Load Impedance For Use With Nominal Input level Connector Sensitivity *2 Nominal Max. before clip CH INPUT MIC (1, 2) –60 dB 3 k ohms 50–600 ohms Mics –72 dBu (0.195 mV) –60 dBu (0.775 mV) –40 dBu (7.75 mV) XLR-3-31 type *3 –16 dB –28 dBu (30.8 mV) –16 dBu (123 mV) +4 dBu (1.23V) CH INPUT LINE (1, 2) –34 dB 10 k ohms 600 ohms Lines –46 dBu (3.88 mV) –34 dBu (15.5 mV) –14 dBu (155 mV) TRS Phone Jack *4 +10 dB – 2 dBu (0.615 V) +10 dBu (2.45 V) +30 dBu (24.5 V) ST CH MIC INPUT (3/4, 5/6) –60 dB 3 k ohms 50–600 ohms Mics –72 dBu (0.195 mV) –60 dBu (0.775 mV) –40 dBu (7.75 mV) XLR-3-31 type *3 –16 dB –28 dBu (30.8 mV) –16 dBu (123 mV) –6 dBu (389 mV) ST CH LINE INPUT (3/4, 5/6) –34 dB 10 k ohms 600 ohms Lines –46 dBu (3.88 mV) –34 dBu (15.5 mV) –14 dBu (155 mV) Phone Jack *5 +10 dB – 2 dBu (0.615 V) +10 dBu (2.45 V) +30 dBu (24.5V) ST CH INPUT (7/8, 9/10 *7) - 10 k ohms 600 ohms Lines –22 dBu (61.5 mV) –10 dBu (245 mV) +10 dBu (2.45 V) Phone Jack *5 RCA Pin Jack CH INSERT IN (1, 2) - 10 k ohms 600 ohms Lines –12 dBu (195 mV) 0 dBu (0.775 V) +20 dBu (7.75 V) Phone Jack (TRS) *6 RETURN (L, R) - 10 k ohms 600 ohms Lines – 8 dBu (308 mV) +4 dBu (1.23 V) +24 dBu (12.3 V) Phone Jack *5 2TR IN (L, R) - 10 k ohms 600 ohms Lines –22 dBV (79.4 mV) –10 dBV (0.316 V) +10 dBV (3.16 V) RCA Pin Jack
	*1: 0 dBu is referenced to 0.775 Vrms. 0 dBV is referenced to 1 Vrms. *2: Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V), or the nominal output level when the unit is set to maximum level. (all faders and level controls are at maximum position.) *3: XLR-3-31 type connectors are balanced. (1=GND, 2=HOT, 3=COLD) *4: Phone Jacks are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND) *5: Phone Jacks are unbalanced. *6: Phone Jacks are unbalanced. (Tip=Out, Ring=In, Sleeve=GND) *7: ST CH IN 9/10 exists only in MW10C

	ANALOG OUTPUT CHARACTERISTICS(MW10C / MW8CX) Connections Actual Source Impedance For Use With Nominal Output level Connector Nominal Levell Max. before clip STEREO OUT (L, R) 150 ohms 10 k ohms Lines +4 dBu (1.23 V) +20 dBu (7.75 V) Phone Jack *8 AUX SEND (EFFECT SEND *9) 150 ohms 10 k ohms Lines +4 dBu (1.23 V) +20 dBu (7.75 V) Phone Jack *8 CH INSERT OUT (CH 1, 2) 75 ohms 10 k ohms Lines 0 dBu (0.775 V) +20 dBu (7.75 V) Phone Jack *6 REC OUT (L, R) 600 ohms 10 k ohms Lines –10 dBV (0.316 V) +10 dBV (3.16 V) RCA Pin Jack MONITOR OUT (L, R) 150 ohms 10 k ohms Lines +4 dBu (1.23 V) +20 dBu (7.75 V) Phone Jack *8 PHONES OUT 100 ohms 40 ohms Phones 3 mW 75 mW Stereo Phone Jack
	*1: 0 dBu is referenced to 0.775 Vrms. 0 dBV is referenced to 1 Vrms. *2: Phone Jacks are impedance balanced. (Tip=HOT, Ring=COLD, Sleeve=GND) *3: Phone Jacks are unbalanced. (Tip=Out, Ring=In, Sleeve=GND) *4: EFFECT SEND exists only in MW8CX

	ANALOG INPUT CHARACTERISTICS(MW12C / MW12CX) Connections Gain Trim Actual Load Impedance For Use With Nominal Input level Connector Sensitivity *2 Nominal Max. before clip CH INPUT MIC (1-4) –60 dB 3 k ohms 50–600 ohms Mics –80 dBu (0.078 mV) –60 dBu (0.775 mV) –40 dBu (7.75 mV) XLR-3-31 type *3 –16 dB –36 dBu (12.3 mV) –16 dBu (123 mV) +4 dBu (1.23V) CH INPUT LINE (1-4) –34 dB 10 k ohms 600 ohms Lines –54 dBu (1.55 mV) –34 dBu (15.5 mV) –14 dBu (155 mV) TRS Phone Jack *4 +10 dB –10 dBu (245 mV) +10 dBu (2.45 V) +30 dBu (24.5 V) ST CH MIC INPUT (5/6, 7/8) –60 dB 3 k ohms 50–600 ohms Mics –80 dBu (0.078 mV) –60 dBu (0.775 mV) –40 dBu (7.75 mV) XLR-3-31 type *3 –16 dB –36 dBu (12.3 mV) –16 dBu (123 mV) –6 dBu (389 mV) ST CH LINE INPUT (5/6, 7/8) –34 dB 10 k ohms 600 ohms Lines –54 dBu (1.55 mV) –34 dBu (15.5 mV) –14 dBu (155 mV) Phone Jack *5 +10 dB –10 dBu (245 mV) +10 dBu (2.45 V) +30 dBu (24.5V) ST CH INPUT (9/10, 11/12) - 10 k ohms 600 ohms Lines –30 dBu (24.5 mV) –10 dBu (245 mV) +10 dBu (2.45 V) Phone Jack *5 RCA Pin Jack CH INSERT IN ( 1-4) - 10 k ohms 600 ohms Lines –20 dBu (77.5 mV) 0 dBu (0.775 V) +20 dBu (7.75 V) Phone Jack (TRS) *6 RETURN (L, R) - 10 k ohms 600 ohms Lines –12 dBu (195 mV) +4 dBu (1.23 V) +24 dBu (12.3 V) Phone Jack *5 2TR IN (L, R) - 10 k ohms 600 ohms Lines –26 dBV (50.1 mV) –10 dBV (0.316 V) +10 dBV (3.16 V) RCA Pin Jack
	*1: 0 dBu is referenced to 0.775 Vrms. 0 dBV is referenced to 1 Vrms. *2: Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V), or the nominal output level when the unit is set to maximum level. (all faders and level controls are at maximum position.) *3: XLR-3-31 type connectors are balanced. (1=GND, 2=HOT, 3=COLD) *4: Phone Jacks are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND) *5: Phone Jacks are unbalanced. *6: Phone Jacks are unbalanced. (Tip=Out, Ring=In, Sleeve=GND)

	ANALOG OUTPUT CHARACTERISTICS(MW12C / MW12CX) Connections Actual Source Impedance For Use With Nominal Output level Connector Nominal Levell Max. before clip STEREO OUT (L, R) 75 ohms 600 ohms Lines +4 dBu (1.23 V) +24 dBu (12.3 V) XLR-3-32 type*2 Phone Jack *3 GROUP OUT (1, 2) 150 ohms 10 k ohms Lines +4 dBu (1.23 V) +20 dBu (7.75 V) Phone Jack *4 AUX SEND (1, 2 *10) (EFFECT SEND *11) 150 ohms 10 k ohms Lines +4 dBu (1.23 V) +20 dBu (7.75 V) Phone Jack *4 CH INSERT OUT (CH 1-4) 75 ohms 10 k ohms Lines 0 dBu (0.775 V) +20 dBu (7.75 V) Phone Jack *5 REC OUT (L, R) 600 ohms 10 k ohms Lines –10 dBV (0.316 V) +10 dBV (3.16 V) RCA Pin Jack MONITOR OUT (L, R) 150 ohms 10 k ohms Lines +4 dBu (1.23 V) +20 dBu (7.75 V) Phone Jack *4 PHONES OUT 100 ohms 40 ohms Phones 3 mW 75 mW Stereo Phone Jack
	*1: 0 dBu is referenced to 0.775 Vrms. 0 dBV is referenced to 1 Vrms. *2: XLR-3-32 type connectors are balanced. (1=GND,2=HOT, 3=COLD) *3: Phone Jacks are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND) *4: Phone Jacks are impedance balanced. (Tip=HOT, Ring=COLD, Sleeve=GND) *5: Phone Jacks are unbalanced. (Tip=Out, Ring=In, Sleeve=GND) *6: AUX SEND 2 exists only in MW12C. *7: EFFECT SEND exists only in MW12CX.

	MW10C / MW8CX / MW12C / MW12CX System Requirements Windows® Vista Computer Windows-based computer with built-in USB interface OS Windows Vista CPU 1 GHz or better Intel Core / Pentium / Celeron processor Memory More than 1 GB Windows® XP Computer Windows-based computer with built-in USB interface OS Windows XP Professional / XP Home Edition CPU 750 MHz or better Intel Core / Pentium / Celeron processor Memory More than 128 MB Macintosh® Computer Macintosh computer with built-in USB interface OS Mac OS X 10.3.3 or higher CPU Macintosh G3 processor 300 MHz or better Memory More than 128 MB

	Cubase AI4 System Requirements Windows® OS Windows XP Professional / XP Home Edition CPU Intel Pentium 1.4 GHz or better Available Memory More than 512 MB Hard Disk Free disk space of 400 MB or more; high-speed hard disk Audio Interface Windows DirectX / ASIO compatible Macintosh® OS Mac OS X 10.4 or higher CPU Power Mac G4 1 GHz or Core Solo 1.5 GHz or better Available Memory More than 512 MB Hard Disk Free disk space of 400 MB or more; high-speed hard disk